Nikon D40 plastic LCD window cover repair (also D40x, D60, and others)
Most, if not all, digital cameras have some sort of plastic cover on top of the LCD. The plastic cover protects and seals the LCD from damage. If the LCD cover gets hit hard enough it cracks. If your LCD underneath looks like someone spilled ink on it, then you’re out of luck, the LCD will need to be replaced as well.
Replacement parts are easy to come by. You’ll need part numbers 1K087-760 (the window) and 1K104-529 (the tape). The cheapest parts can be head directly from Nikon 1-310-414-8107. You don’t need to be an authorized dealer or repair shop, anyone can call and order parts from Nikon. They’ll even look up parts for you if you don’t know the part number.
Replacing the LCD window is easy enough. Start by removing the bottom cover. Keep track of the screws. There are a few near the batter compartment that are longer, and one hidden screw beneath a small flap also near the battery compartment. Also don’t forget the ones near the bottom of the lens mount.
The bottom cover should lift off, nothing else is attached to it. Next remove the rear cover. Its got screws on each side, near the eyepiece, and under the SD card door. Remove the SD card. The rear case will not come out with a card installed.
The rear case will be held on by one ribbon cable. Flip the latch up and slip out the ribbon cable.
Flip the case over and the remove the screws holding the metal backing plate to the rear case.
Getting the LCD cover out of the rear case can be tricky, the glue is very strong. I pushed the cover from the back and it cracked in two, then I removed the broken pieces.
Remove any of the doulbe sided tape that did nto come out with ehthe LCD cover.
Apply the new tape to the rear case keeping one side of the paper backing on, that way you can press down on the tape getting a good seal.
The new LCD cover should come with some protective film. Remove the film on the back and align one side to the rear case. Avoid touching the uncovered side of the LCD cover, finger prints will be stuck behind the cover FOREVER.
If the buttons fall out don’t worry, they are all keyed and will only go in one spot.
Now put it all back together!
where did you buy the lcd window replacement?
Cheaper and more reliable to order directly from Nikon like the article says. Just got my parts today.
BTW, excellent post! I just finished replacing the window on my D40 using this. Every instruction is dead on. Only tricky part was figuring how to flip up the black latch to release the ribbon cable. Just get a thin flat head under and gently flip up. Take care not to scratch or damage the ribbon cable.
Great post. I’m having a hard time reseating the ribbon cable. Do you have any hints? Or photos of this part of the process? Thanks!
Make sure the flip up plastic lock is up. The ribbon will not go very far into the connector. The latch is what holds the ribbon in place, not the contacts.
I don’t understand why you needed to take everything apart for this. The plastic window can be prized out from the outside with a small screwdriver, then a new window inserted directly from the outside.
Did you need to replace the LCD as well?
The window is held on with very strong adhesive. If you want to risk cracking your case and gouging your LCD, then by all means take a screwdriver to it.
I’m glad I found your page. I almost bought my replacement glass through eBay where it would have cost around $20 until I read your post. Instead Nikon sells the glass and tape directly for only $5.50 total. I will say this, I think I agree with Rene. Not sure you have to take the entire back off to do this. You can carefully pries the old glass away using the proper tools. Here is a video example: http://www.youtube.com/watch?v=B8KVKTAe_Ok
I don’t live in US and Nikon in this country refuse to sell parts to consumers, requiring me to send my camera back to their service department for repairs. I don’t live in the capital where the service center is located, so it would probably have cost me well over $100 with shipping and all included. I was able to buy the parts from Nikon US shipped to a friend in US who was kind enough to forward it to me. If I had not had that option Ebay would have been a good alternative.
I was able to pries the old glass off without damaging the LCD at all. Of course you want to be careful doing this, that goes without saying, but I feel personally it would have been a bigger risk taking everything apart and ending up with a bunch of parts I didn’t know how to fit together again and/or damage in other ways.
The German video is interesting in that it seems to skip over removing the old glue (I used a small screwdriver to carefully remove the gum/glue bits) and they also didn’t seem to use the tape (1K104-529) before inserting the glass.
I agree, I noticed the same thing in the German video. I assume they must have applied the tape prior to putting the glass back in place.
I forgot to mention that Nikon US would only ship to a US address. That kinda made my reference to Ebay a little incoherent.
No worries!!
This technique works very well, I have followed it and changed my cracked Nikon D40 screen successfully thanks! I first tried to go the simpler route shown on you tube of popping the screen out from the front without taking the camera apart, but the screen is very firmly fixed and I decided there was too much risk of damage. I did two things differently, 1: you do not need to remove the 2 screws under the SD card door, they do not hold the back on. 2: I did not disconnect the ribbon cable as I was not confident on how to do this, I left it connected and unscrewed the metal plate to seperate the back from the camera, leaving the LCD attached to the body by the ribbon. Another tip, I printed out the relevant diagrams from the service manual and placed each screw on the printed picture in its correct location to keep track of each one for re-assembly. Nikon UK supplied new screen for around £5
Wonderful post!!! I was quoted over $100 to have the camera repaired (just to replace the lcd window). The parts were less than $10 directly from Nikon. It took me a little under one hour to replace the window from start to finish. It probably could have been done a lot quicker, but I was taking my time and making sure that I had everything documented, as it’s easier to take something apart than put it back together.
The instructions were dead on, although I might suggest a couple of simple diagrams of the camera (back, side, etc.) outlining the different screws, as some of them are different sizes. I didn’t experience any problems with the ribbon cable, as I left it attached and just carefully worked around it (I have a DX40). My camera was in excellent shape, but unfortunately I picked up a couple of noticable scratches on the window. It looks brand new now.
Much thanks for taking the time to post these detailed instructions!!!